Justing, s.r.o.

FICO / Final inspection of needle & lancet

admin — Wed, 17 Feb 2010 13:57:23 +0000

The equipment is intended for the final inspection of lancets, where the subject of the inspection is the prescribed length of lancets and the sharpness of the point.

The equipment is solved as an automatic one, controlled by a program in the computer. The operator replaces the cartridges with lancets in the magazine and at the output from the equipment. The operator monitors individual operations and continuously the resulting quality of the work.

Position	Parameter	Value
Dimensions	height	1600 mm
	width	1250 mm
	depth	605 mm
Weight		150 kg
Output		max. 12 pcs/sec
Size of tubes / lancets	diameter	∅ 0,3 ÷ 1,5 mm
	length	20 ÷ 80 mm
Conveyor speed		approx. 1 rev./40 sec.
Power supply		230V/50Hz, 1500 VA

SLK / Siliconing of point

admin — Wed, 17 Feb 2010 13:40:22 +0000

The equipment serves for siliconing of points of lancets and cannulas.

The equipment for siliconing has a unique jet system for siliconing and blasting. The lancets (cannulae) are loaded into a mass magazine (approx. 50 000 pcs), from where they are picked by a picking wheel. They are led through a system of jets for siliconing and blasting, a drying jet and are collected into a magazine with a capacity of approx. 10 000 pcs.

After the process of siliconing, it is necessary to carry out another technological operation – hardening (branching) of the silicone coating.

Considering the fact, that the applied silicone layer is ultra thin, it is not possible to measure it. The area of silicon- ing can be seen when the lancets are in a bundle. The siliconing effect can be measured only by measuring the pricking force. In our portfolio, we also have an equipment for measuring the pricking force.

Parameter	Value
Height	1600 mm
Width	1250 mm
Depth	605 mm
Weight	80 kg
Output	max. 12 pcs/sec.
Diameter of needles	∅ 0,2 ÷ 2 mm
Length of needle	20 ÷ 80 mm
Conveyor speed	approx. 1 RPM
Drying temperature	50°C
Noise	max. 76 dbA
Compressed air consump.	max. 6 m3/h, 1,5 MPa
Power supply	1, N, PE 230V, 50 Hz

ECHA / Electro-chemical grinding of front

admin — Wed, 17 Feb 2010 12:42:39 +0000

The grinding machine ECHA Uni 501 is designed for automatic flat grinding by an electrochemical procedure.

Using the necessary fixing elements it enables grinding of cut tube and canulla fronts including sequential deburring.

For more information view the attached Catalogue Sheet and address us with your enquiry.

ECOBOS – Needle point grinder

admin — Wed, 17 Feb 2010 12:08:41 +0000

The maschine is designed for grinding the sharp edges of injection needles.

The grinding of both edges of tube is possible.

The preset of equipment and working method depends on the number of furnished, sorted needles and other conditions.

Operation can be done by one worker, who operates one grinding and one blasting equipment.

Position	Parameter	Value
Grinded tube/wire	Diameters	∅ 0,25 ÷ 2,5 mm
	Lengths	10 ÷ 100 mm
	ALPHA angle	min. 7° ÷ max. 30°
Grinding wheel	Ext. diameter	455 mm
	Bore diameter	127 mm
	Width	80 mm
Dimensions	Length	1650 mm
	Width	3100 mm
	Height	1600 mm
	Weight	2600 kg
Energy supplies	Power	3, N, PE, 400V, 50Hz

Straightening and cutting equipment for tube and wire

admin — Wed, 20 Jan 2010 12:53:05 +0000

After reduction to desired dimension the tubes need to be straightened and cut to desired lengths.

Tubes wound on reels are clamped to an unwinding stand. The tube is travelling through cleaning jaws to the straightening area.

Straightened tubes are then cut to desired lengths either pneumatically or electrically.

One operator usually operates two pieces of straightening and cutting equipment.

Parameter	Value
Length x Width x Height	2500 x 600 x 1300 mm
Weight	120 kg
Straightening and cutting range	∅ 0,3 - 1,2 mm
Available cut lengths	10 mm + more
Length tolerance of cut tubes	± 0,15 mm
Maximal output	240 pieces/minute